← Back to the help centre

Exit codes of the Noviscan installer for Windows

Read the French version

The Noviscan installer for Windows returns a numeric code when it finishes running. When Noviscan is installed from the Microsoft Store, the installation runs without any window: if it fails, this is the code the Store shows you.

These codes are those of Inno Setup, the tool that builds the installer. Each one is described below: what it means for you, then what to do.

The codes at a glance

CodeWhat it means
0Installation successful
1The installer could not start
2Installation cancelled before it started
3Fatal error during preparation
4Fatal error during installation
5Installation cancelled part-way through
6Installer forcibly stopped
7The installation cannot continue
8Restart required

Code 0 — Installation successful

What it means

The installation completed normally. Noviscan is installed on your computer.

What to do

  1. Nothing: you can start Noviscan.

Code 1 — The installer could not start

What it means

The installer failed during its initialisation, before it could begin the installation.

What to do

  1. Restart the computer.
  2. Run the installation again from the Microsoft Store.

If the problem persists, write to us using the contact form, stating the exit code, your version of Windows and the version of Noviscan you were installing.

Code 2 — Installation cancelled before it started

What it means

The installation was cancelled before the actual installation began: someone clicked “Cancel” in the wizard, or answered “No” to the opening message. Nothing was installed.

What to do

  1. Run the installation again whenever you wish, and see it through to the end.

Code 3 — Fatal error during preparation

What it means

A fatal error occurred while moving on to the actual installation. This is very rare: it mostly happens when Windows is running out of memory or resources.

What to do

  1. Close any open applications.
  2. Restart the computer.
  3. Run the installation again.

If the problem persists, write to us using the contact form, stating the exit code, your version of Windows and the version of Noviscan you were installing.

Code 4 — Fatal error during installation

What it means

A fatal error occurred during the actual installation, which did not complete. A full disk, for example, leads to this code: the installer does not return a separate code for that case.

What to do

  1. Check that there is free space left on the disk where Noviscan is being installed, and free some up if needed.
  2. Close Noviscan if it is open.
  3. Run the installation again.
  4. If the failure happens again, restart the computer, then try again.

If the problem persists, write to us using the contact form, stating the exit code, your version of Windows and the version of Noviscan you were installing.

Code 5 — Installation cancelled part-way through

What it means

The installation was interrupted while it was in progress: someone clicked “Cancel”, or chose “Cancel installation” in an error message. Such a message appears in particular when a file to be replaced is still in use.

What to do

  1. Close Noviscan if it is open.
  2. Run the installation again, and see it through to the end.

Code 6 — Installer forcibly stopped

What it means

The installer was forcibly stopped by a development tool. This code does not occur during an ordinary installation.

What to do

  1. Run the installation again.

If the problem persists, write to us using the contact form, stating the exit code, your version of Windows and the version of Noviscan you were installing.

Code 7 — The installation cannot continue

What it means

At the “Preparing to Install” stage, the installer found that it could not proceed. Nothing was installed.

What to do

  1. Close Noviscan if it is open.
  2. Run the installation again.
  3. If the code comes back, restart the computer, then try again.

If the problem persists, write to us using the contact form, stating the exit code, your version of Windows and the version of Noviscan you were installing.

Code 8 — Restart required

What it means

At the “Preparing to Install” stage, the installer found that it could not proceed until the computer has been restarted—for example because a Windows update or a previous installation is waiting for that restart.

What to do

  1. Save any work in progress.
  2. Restart the computer.
  3. Run the installation again.

If the problem persists, write to us using the contact form, stating the exit code, your version of Windows and the version of Noviscan you were installing.

A code that is not in this list

Inno Setup does not document any code other than these. If you see a different one, note it down exactly as displayed.

If the problem persists, write to us using the contact form, stating the exit code, your version of Windows and the version of Noviscan you were installing.